C. Adalian and P. Morlier, "WOOD MODEL" for the dynamic behaviour of wood in multiaxial compression, Holz als Roh- und Werkstoff, vol.60, issue.6, pp.433-439, 2002.
DOI : 10.1007/s00107-002-0333-x

G. Almeida and R. Hernández, Changes in physical properties of yellow birch below and above the fiber saturation point, Wood Fiber Sci, vol.38, issue.1, pp.74-83, 2006.

J. Dumail and L. Salmèn, Compression Behaviour of Saturated Wood Perpendicular to Grain under Large Deformations. Comparison Between Water-Saturated and Ethylene Glycol-Saturated Wood, Holzforschung, vol.51, issue.4, pp.296-302, 1997.
DOI : 10.1515/hfsg.1997.51.4.296

K. Easterling, R. Harrysson, L. Gibson, and M. Ashby, On the Mechanics of Balsa and Other Woods, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, vol.383, issue.1784, pp.31-41, 1982.
DOI : 10.1098/rspa.1982.0118

F. Eyma, P. Méausoone, P. Larricq, and R. Marchal, Utilization of a dynamometric pendulum to estimate cutting forces involved during routing. Comparison with actual calculated values, Annals of Forest Science, vol.62, issue.5, pp.441-447, 2005.
DOI : 10.1051/forest:2005040

URL : https://hal.archives-ouvertes.fr/hal-00883902

P. François, Plasticity of wood in multiaxial compression: application to the absorption of the mechanical energy (in French) thesis, l'Université Bordeaux I Gerhards CC (1982) Effect of moisture content and temperature on the mechanical properties of wood: an analysis of immediate effects, pp.4-36, 1992.

D. Goring, Thermal softening of lignin, hemicellulose and cellulose. Pulp and Paper Canada Magazine, pp.517-527, 1963.

G. Irvine, The glass transitions of lignin and hemicellulose and their measurement by differential thermal analysis, Tappi J, vol.67, issue.5, pp.118-121, 1984.

S. Mindess, P. Sukontasukkul, and F. Lam, Fracture of air-dried and fully saturated parallel strand lumber (PSL) under impact loading, Wood Science and Technology, vol.38, issue.3, pp.227-235, 2004.
DOI : 10.1007/s00226-004-0229-5

P. Perré, Experimental device for the accurate determination of wood-water relations on microsamples, Holzforschung, vol.61, pp.419-429, 2007.

P. Perré and I. Turner, The use of numerical simulation as a cognitive tool for studying the microwave drying of softwood in an over-sized waveguide, Wood Science and Technology, vol.33, issue.6, pp.445-464, 1999.
DOI : 10.1007/s002260050129

V. Placet, J. Passard, and P. Perré, Differences of the viscoelastic properties of normal and reaction green wood across the grain measured by harmonic tests in the range of 0 °C to 95 °C, Holzforschung, vol.61, pp.548-557, 2007.

V. Placet, J. Passard, and P. Perré, Viscoelastic properties of wood across the grain measured under water-saturated conditions up to 135????C: evidence of thermal degradation, Journal of Materials Science, vol.52, issue.65, pp.3210-3217, 2008.
DOI : 10.1007/s10853-008-2546-9

URL : https://hal.archives-ouvertes.fr/hal-00395497

S. Reid and C. Peng, Dynamic uniaxial crushing of wood, International Journal of Impact Engineering, vol.19, issue.5-6, pp.5-6, 1997.
DOI : 10.1016/S0734-743X(97)00016-X

M. Renaud, M. Rueff, and A. Rocaboy, Mechanical behaviour of saturated wood under compression, Wood Science and Technology, vol.30, issue.3, pp.153-164, 1996.
DOI : 10.1007/BF00231630

T. Siewert and K. Schmieder, Pendulum impact machines: procedures and specimens for verification. ASTM publications Effect of tup geometry on impact behaviour of parallel strand lumber (PSL), Philadelphia Sukontasukkul P, Lam F J KMITNB, vol.14, issue.2, pp.1-7, 1995.

L. Tavares and R. King, Single-particle fracture under impact loading, International Journal of Mineral Processing, vol.54, issue.1, pp.1-28, 1998.
DOI : 10.1016/S0301-7516(98)00005-2

N. Wang, S. Mindess, and K. Ko, Fibre reinforced concrete beams under impact loading, Cement and Concrete Research, vol.26, issue.3, pp.363-376, 1996.
DOI : 10.1016/S0008-8846(96)85024-1

S. Widehammar, Stress-strain relationships for spruce wood: Influence of strain rate, moisture content and loading direction, Experimental Mechanics, vol.33, issue.2, pp.44-48, 2004.
DOI : 10.1007/BF02427975